01
Separators & treaters
Two- and three-phase, horizontal and vertical. Heated treaters with firetubes, BMS-ready. Internals sized to your flow — weirs, buckets, mist pads, sand jets.
MAX120" OD · 60' S/S · 2 160 psig
ASME VIII Div. 1Vessels & skids · Grande Prairie, AB
Built to code.
Shipped on the date we quoted.
ASME pressure vessels and process skids, fabricated in Grande Prairie for producers and EPCs across Western Canada. Two bays, 40 tonnes of hook, and a data book that's finished before the truck is.
OpenBay 2 · week of Nov 16 · quote now to hold itDWG NO. CF-2214 · REV C · ASME VIII DIV 1 · CRN PENDINGFront elevation · Sheet 1 of 4
Stamps & registrations
- UASME U
- U2U2
- SS stamps
- CRN
- ABSA AQP
- CWB Div. 1
- COR
01 / Capabilities
Six things.
Built every week.
We don't do structural steel, tanks or field welding on the side. Pressure equipment and the skids it sits on — designed to your datasheet, stamped, tested and shipped from one yard.
02
Scrubbers & knockouts
Inlet, suction and discharge scrubbers, flare knockout drums, filter separators. Vane packs and mesh pads specified, not guessed.
MAX96" OD · 40' S/S · 3 705 psig
03
Line heaters
Indirect water-bath heaters with removable firetubes and coil bundles. Process coils hydrotested separately, then as an assembly.
MAX8 MMBtu/h · coils to 5 000 psig
04
Meter & injection skids
Orifice, Coriolis and ultrasonic meter runs to AER Directive 017. Chemical and methanol injection with pumps, tanks and heat trace.
MAX12" runs · 14' × 48' skids
05
Piping spools
B31.3 process piping in carbon, low-temp and stainless. Spool-numbered, weld-mapped, tagged to your isometrics — shipped in install order.
RANGE½" to 36" NPS · to Sch 160
06
Modular packages
Vessels, piping, electrical and instrumentation built into one shippable module. Pre-wired, loop-checked, ready to set and tie in.
MAX16' × 80' × 16' · 70 t per module
02 / Shop capacity
What the floor looks like for the next 12 weeks.
This is the board on the wall of our shop office, updated every Friday by the shop super. If a week is green, it's open. If you need it, quote now — slots go to the first signed PO.
2026
OCT
NOV
DEC
WEEK OF
5
12
19
26
2
9
16
23
30
7
14
21
Bay 12 × 20 t cranes
J-22883Φ separators ×3 · Calgary EPC
J-2297Line heaters ×2 · Montney producer
J-2306Compressor scrubber module
XMAS
Bay 210 t + 5 t cranes
J-2291Meter skids ×4 · D-017
J-2295Spools · 140 pcs · B31.3
J-2309Tentative · PO pending
XMAS
Blast & paintHeated booth
2284
2291
J-2288SSPC-SP10
2295
J-2297Coil + shell
2306
XMAS
Swipe the board →
Next open slot: Bay 2, week of Nov 16 — quote now to hold it.
Hold Bay 2 · Nov 16- Bay 1
- 60 × 240 ft
- 2 × 20 t overhead cranes, 40 t tandem. 34 ft under the hook.
- Bay 2
- 50 × 160 ft
- 10 t + 5 t cranes. Skids, spools and small-bore vessels.
- Max vessel
- 144" OD × 80 ft
- Seam to seam, up to 70 t shipping weight.
- Plate rolling
- 1¼" × 10 ft
- Four-roll plate roll. Heads sourced from certified mills.
- Hydrotest
- To 15 000 psig
- 40 ft test bed, chart-recorded, witnessed by your inspector.
- NDE
- RT · PAUT · MT · PT
- Coordinated in-house. Level II techs on site within 24 hours.
- Coatings
- Blast & paint
- Heated 70 × 24 × 22 ft booth. NACE-certified coatings inspector.
- Yard
- 7 acres
- Highway 43 access. Step-deck, Scheuerle and B-train loading.
03 / Quality
Five hold points.
No shortcuts between them.
Our ABSA-accepted quality program runs every job the same way, whether it's one scrubber or a forty-tonne module. Your inspector gets an ITP at kickoff and a phone call before every hold point.
-
1
MTR review
Every plate, pipe, forging and fitting checked against its mill test report — heat numbers transferred and logged before it's cut.
Hold point -
2
Fit-up inspection
Bevels, root gaps, alignment and nozzle orientation checked against the drawing by our QC inspector before a root pass goes in.
Hold point -
3
Weld map & NDE
Each weld tied to a welder, a WPS and an NDE report. RT, PAUT, MT and PT to code — or to your spec, whichever is stricter.
Witness point -
4
Hydrotest
Calibrated gauges, a chart recorder and the hold time written on the ITP. Witnessed by the Authorized Inspector and, if you want, by you.
Hold point -
5
Data book
Compiled as we build, not after. Reviewed by QC, indexed and sent electronically the day the vessel ships.
Ships with it
Every vessel ships with a complete data book.
Not "to follow." Not a week later after three emails. In the truck's paperwork and in your inbox the same day.
- 01Manufacturer's Data Report (U-1A / U-1)
- 02CRN registration & ABSA documentation
- 03Mill test reports, heat-number traced
- 04Weld map with welder IDs
- 05WPS / PQR / welder qualifications
- 06NDE reports & RT film or PAUT data
- 07Hydrotest chart & gauge calibrations
- 08Coating report with DFT readings
- 09Signed ITP & as-built drawings
- 10Nameplate rubbing
04 / Track record
Numbers we'd put on a bid.
Twenty-two years building for operators in the Montney, Duvernay and Peace River Arch — most of whom found us through someone who'd already worked with us.
1 140
Vessels and skids shipped since 2004.
96.4%
Shipped on or before the date on the quote.
Trailing 36 months · 211 jobs22
Years in Grande Prairie. Same yard, same owner.
412k
Hours worked since our last recordable.
COR holder · audited 2026We sent the RFQ cold on a Tuesday. Budget number Thursday, firm quote the next week, and the data book was complete the day the separators landed. That's rarer than it should be.
Their QC inspector calls us before a hold point, not after. Four years of skids and we haven't written them a single NCR.
Recently out the door
Q3 2026 · Client names withheld05 / Careers
We're hiring B-pressure welders, fitters, and a QC inspector.
Day shift. Home every night. Rates posted right here, because "competitive" doesn't tell you anything. If you can pass a bend test, we want to meet you this week.
B-Pressure Welder
$50–$56 / hrSMAW and GTAW on carbon and low-temp; FCAW a plus. Vessels, nozzles and heavy-wall spools. Top-of-market for the Peace Country — the high end goes to welders who can run stainless root and hot pass.
3 openings · Shop · Grande PrairiePressure Fitter
$44–$50 / hrRead isos and vessel drawings, lay out nozzles, fit to tolerance without being babysat. Journeyman Steamfitter-Pipefitter or Welder with real fitting time.
2 openings · Shop · Grande PrairieQC Inspector
$105–$125k / yrOwn the ITP from MTR review to data book. CWB Level 2 or API 510 required; ASME VIII and ABSA quality program experience strongly preferred.
1 opening · Salaried · Grande Prairie4 × 10s, Mon–ThuDay shift. Friday OT at time-and-a-half when you want it, never mandatory.
Paid test dayYour bend test is on our clock. Pass, and you start the next Monday.
Benefits from day oneHealth, dental, vision. RRSP matched to 4%.
Tickets paidCWB, B-pressure renewals, Red Seal upgrading. $1,500 yearly tool allowance.
Field crew: 14 / 7Site tie-ins on rotation. LOA and travel paid, mileage from the yard.
Consumables on usRod, wire, lenses, gloves. You bring your hood and your hands.
Apply in 60 seconds.
No résumé needed. The shop super calls you back within one business day.
Got it.
The shop super will call you within one business day to book your test. Bring your ticket and your hood.
06 / Request for quote
Send the RFQ. We'll send a number.
48 hBudget pricingA real number with a shop-day estimate — enough to carry in your AFE.
5 daysFirm quoteItemized, with a ship date tied to a bay slot on the board above.
1 callAn estimator who reads drawingsClarifications come as one list, not a drip of emails.
Estimating
rfq@chinchagafab.example
(780) 555-0142 · Mon–Fri, 6:30–5:00
RFQ received.
An estimator has it now.
- Budget pricing by —
- Clarification list, if we have one, in a single email
- Firm quote with a held bay slot by —